Installing the rtl8180-sa2400 Linux kernel driver
Released under the terms of GNU General Public Licence (GPL)
Copyright(c) Andrea Merello - 2004, Install instructions by Rick Bronson
NOTE: These instructions were written for a Knoppix 3.6 (using Linux
2.6.7 kernel)
1. Hardware prerequisites
1.1 One of the following devices:
1.1.1 Realtek card, Man ID = 0x10ec. Device ID =0x8180 (make sure it
mount sa2400 radio. Many cards do, many don't)
1.1.2 Belkin F5D6001 PCI card, Man ID = 0x1799, Device ID =0x6001
(Version 3)
1.1.3 Belkin F5D6020 Version 3 (3000) Cardbus card, , Man ID =
0x1799, Device ID =0x6020 NOTE: version 1 and 2 will not work
1.1.4 DLINK card, Man ID = 0x1799, 0x1186, Device ID =0x3300
(A DWL-610 is working here, but I'm not sure all these cards
have rtl8180 & sa2400)
2. Software prerequisites
2.1 Linux 2.6.0 or greater, 2.4 might work but you'll have to do some
hacking.
3. Instructions
3.1 Get latest driver from
http://sourceforge.net/projects/rtl8180-sa2400 (in this example
we'll use rtl8180-0.9.1) and build:
tar xzf rtl8180-0.9.1.tar.gz
cd rtl8180-0.9.1
make
(naturally, substitute 0.9.1 with the current version number)
You can ignore any "no CRC" warnings.
3.2 Module loading (order is important)
for user convenience a ./module_load script is provided.
Anyway if you want to do manually:
sudo insmod ieee80211-r8180_crypt.ko
# you may or may not have to do this following step, Knoppix needs it
sudo insmod /usr/src/linux/lib/crc32.ko
# you will also need ARC4 support in kernel or by loading module
sudo insmod ieee80211_crypt_wep.ko
sudo insmod ieee80211-r8180.ko
sudo insmod r8180.ko
Once the above is done, you can do some checks to verify if all went
OK:
Doing
cat /proc/modules
Gives:
---------------------------------------
r8180 34312 0 - Live 0xc6c55000
ieee80211-r8180 25988 1 r8180, Live 0xc6c41000
ieee80211_crypt_wep 9216 0 - Live 0xc6c34000
crc32 8064 1 ieee80211_crypt_wep, Live 0xc6c31000
ieee80211-r8180_crypt 9092 2 ieee80211-r8180,ieee80211_crypt_wep, Live 0xc6c2d000
---------------------------------------
If you do:
dmesg
You should see something like:
---------------------------
rtl8180: Card MAC address is XX:XX:XX:XX:XX:XX
...
rtl8180: driver probe completed
---------------------------
In this output you should see also other detail like if you have a
digital or analog PHY. support for the latter is experimental, please
report..
If you do:
ifconfig -a
You should see
---------------------------
wlan0 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:XX
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:9 Base address:0x4800
---------------------------
Doing:
cat /proc/interrupts
You should see something like:
---------------------------
9: 0 ..... , wlan0
---------------------------
Where '9' could be any number
If you have a CARDBUS card, doing "cardctl ident" should say something
like:
---------------------------------------
Socket 1:
product info: "Realtek", "Rtl8180"
manfid: 0x0000, 0x024c
function: 6 (network)
---------------------------------------
Doing:
iwconfig
Shows:
---------------------------
wlan0 IEEE 802.11b ESSID:"" Nickname:""
NWID:off/any Mode:Managed Frequency:2.462GHz
Access Point: 00:11:50:0A:07:85 Bit Rate=-1.07375e+06kb/s Tx-Power:off
Sensitivity=1074102348/0
Retry:off RTS thr=-1073745104 B Fragment thr:off
Power Management:off
---------------------------
For now not all parameters are meaningful (like Sensivity).
3.3 Setup
sudo ifconfig wlan0 up
At this point, if you are near an AP or wireless router you should
start getting interrupts:
cat /proc/interrupts
---------------------------
9: 500 ...., wlan0
---------------------------
The second number increments. Note that this happens also if you have
other peripherical on the same interrupt line and you use them.
Doing:
ifconfig
Shows (note RX bytes):
---------------------------
wlan0 Link encap:UNSPEC HWaddr 00-30-BD-4D-8F-9E-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2170 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:93343 (91.1 KiB) TX bytes:0 (0.0 b)
Interrupt:9 Base address:0x4000
---------------------------
If you do:
iwlist scan
If you are in range of an AP or wireless router, you should see
something like:
---------------------------
wlan0 Scan completed :
Cell 01 - Address: 00:11:50:0A:07:85
ESSID:"solar"
Mode:Master
Frequency:2.462GHz (channel 11)
Bit Rate:1Mb/s
Bit Rate:2Mb/s
Bit Rate:5.5Mb/s
Bit Rate:11Mb/s
Bit Rate:18Mb/s
Bit Rate:24Mb/s
Bit Rate:36Mb/s
Bit Rate:54Mb/s
Quality=21/100 Signal level=-28 dBm Noise level=-256 dBm
Encryption key:off
---------------------------
3.4 Test
Now set your SSID:
sudo iwconfig wlan0 essid solar
Substitute 'solar' (my essid) with your essid.
Set your address (you may want to use different numbers here):
sudo ifconfig wlan0 broadcast 192.168.0.255 netmask 255.255.255.0 192.168.0.100
Add a route, if you need it:
sudo route add default gw 192.168.0.1 dev wlan0
Try pinging another host (like the wireless router itself):
ping 192.168.0.1
For further usage hint (es. setting WEP key or monitor mode see README file)
3.3 Installing permanently (so the driver is loaded when you reboot).
< Not done yet >
3.4 Diagnostics
Some commands you can use to try to figure out what's gone wrong:
lsmod
dmesg
ifconfig -a
iwconfig
cat /proc/iomem
cat /proc/interrupts
cardctl ident
iwlist scan
In particular dmesg output is very useful/appreciated in report
